{"product_id":"697213-timer-kit-12-hr-ezgo-ccw-electromechanical-timer-with-automatic-shutoff-replaces-697125-11562g1-and-others","title":"697213 - Timer Kit - 12 HR EZGO CCW Electromechanical Timer with Automatic Shutoff - Replaces 697125, 11562G1 and others","description":"\u003cp\u003eThis is an EZGO 12 hour counter-clockwise rotation manual timer and is for EZGO golf cart chargers prior to Total Charger II. Wind it clockwise to set the desired run time, the timer runs counter-clockwise as it counts down to the OFF position. These timers are for manual chargers that do not rely on voltage-sensing circuitry to energize. They will charge batteries regardless of initial battery voltage.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eTimer mounts with 2 screws through the face of the charger. 1\/4 inch screws are supplied for use in standard thickness sheet metal charger panels. Longer 3\/8 inch screws are supplied for use when the charger panel is thicker than normal - for example, 1\/8 to 3\/16 inch thick.\u003cbr\u003eNOTE: Only use the longer screws if necessary, otherwise they may intrude to deep into the timer mechanism and damage it.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eFits EZ-GO battery chargers for golf carts and industrial equipment (confirm fitment before ordering). \u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eThis kit includes all the necessary components to use this timer in retrofit applications where the original charger timer is no longer available. Check dimensions and electrical connection requirements closely to insure that this timer will fit in the existing charger case. \u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eNo special tools are required for installation. However, we have tool suggestions, depending on the type of installation.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eIf you are replacing the timer in an existing EZGO charger:\u003cbr\u003e- Phillips screwdriver (for the mounting screws)\u003cbr\u003e- Needle-nose pliers (to aid in removing and attaching push-on wire terminals)\u003cbr\u003e- Multimeter\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eIf you are installing this timer as a retrofit part and the stem hole and mounting holes do not line up, you will also need a drill and bits to make new holes in the charger cabinet:\u003cbr\u003e- Electric drill\u003cbr\u003e- 3\/16\" bit (for the mounting screw holes)\u003cbr\u003e- 3\/8\" bit (for the central stem hole)\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eThis timer is made to OEM specifications in the USA by the OEM timer manufacturer for EZ-GO. It is manufactured to meet or exceed industry standards. It is an exact fit replacement component.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eReplaces\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eCART PARTS 18052G6\u003cbr\u003eCOLUMBIA HD 66057-65\u003cbr\u003eEZGO 11562G1\u003cbr\u003eEZGO 11562-G1\u003cbr\u003eEZGO 14169G1\u003cbr\u003eEZGO 14169-G1\u003cbr\u003eEZGO 14466G1\u003cbr\u003eEZGO 14466-G1\u003cbr\u003eEZGO 17572G1\u003cbr\u003eEZGO 17572-G1\u003cbr\u003eEZGO 18052G1\u003cbr\u003eEZGO 18052-G1\u003cbr\u003eEZGO 18052G6\u003cbr\u003eEZGO 18052-G6\u003cbr\u003eEZGO 697125\u003cbr\u003eKARRIOR 769-13\u003cbr\u003eNOLAND 1212\u003c\/p\u003e\n\u003ch5\u003eWhat's in the Box\u003c\/h5\u003e\n\u003cp\u003e1 - 697211, Timer\u003cbr\u003e2 - 609097, 8-32 x 1\/4\" rolling thread mounting screw (standard length)\u003cbr\u003e2 - 609098, 8-32 x 3\/8\" rolling thread mounting screw (long length for thicker cabinet panels)\u003cbr\u003e1 - 696553, skirted knob with set screw\u003cbr\u003e1 - 609066, Dial label (standard left side mount)\u003cbr\u003e1 - 609067, Dial label (reversed right side mount)\u003cbr\u003e1 - Screwdriver (3mm) for knob set screw\u003c\/p\u003e\n\u003ch5\u003eSpecifications (Timer)\u003c\/h5\u003e\n\u003cp\u003eNominal Description: 12 Hour Electromechanical\u003cbr\u003eTerminals: 0.250 in. flat male \u003cbr\u003eTimer Motor Rating: 115V, 60Hz\u003cbr\u003eSwitch Rating: 1\/3HP, 15 A @ 125 VAC, 7.5  A @ 250 VAC, 25 A @ 250VAC (HTR)\u003cbr\u003eStem Diameter: 0.250 in. \u003cbr\u003eStem Length: 0.720 in. \u003cbr\u003eStem Width at Flat: 0.185 in. \u003cbr\u003eStem Flat Length: 0.500 in. \u003cbr\u003eMounting Hole Spacing: 1.125 in. (on stem centerline, vertical orientation)\u003cbr\u003eMounting Hole Diameter: 0.310 in. min\u003cbr\u003eLength (Depth, body):  2.073 in.\u003cbr\u003eLength (Depth, including stem): 2.793 in. max\u003cbr\u003eWidth: 2.609 in.\u003cbr\u003eHeight: 3.335 in.\u003cbr\u003eWeight: 0.432 lbs (196 g)\u003cbr\u003e\u003c\/p\u003e\n\u003ch5\u003eInformation Downloads\u003c\/h5\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0325\/5471\/3133\/files\/697213_Installation_Sheet_-_rev_06-2026.pdf?v=1785458528\" title=\"697213 Timer Kit Installation Sheet\" rel=\"noopener\" target=\"_blank\"\u003e697213 Timer Kit Installation Sheet\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"Power Forged®","offers":[{"title":"Default Title","offer_id":52143193686236,"sku":"697213","price":89.85,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0325\/5471\/3133\/files\/697213_b.jpg?v=1785458724","url":"https:\/\/www.plpbattery.com\/products\/697213-timer-kit-12-hr-ezgo-ccw-electromechanical-timer-with-automatic-shutoff-replaces-697125-11562g1-and-others","provider":"PLP Battery Supply","version":"1.0","type":"link"}