Repair Parts - Chargers, Testers, Jump Eqpt

Heavy-Duty Positive-Base Rectifier. Designed for use in chargers with continuous-duty output ratings up to 80 Amps,and "Boost" ratings up to 450 Am...

48V State-of-Charge & Battery Test Meter for 48 Volt DC systems. Also used for Charging System Monitoring. 41-60V scale with Discharged-Chargin...

0-100 Amp Clamp-Mount Heavy-Duty DC Amp Meter for Battery Chargers. Original Replacement for Various 50-90 Amp Chargers. Also an easy retro-fit in ...

Axle Cap Nut, Push-On 1/2" Decorative Black Plastic Pal Nut 1 cap each, bulk packaged. 10-Pack available. Axle OD: 0.500" (1/2")Cap OD: 1.30"Height...

696029 - Stud Mount Diode, 150A, 3/8" Stud, 600 PRV Negative (Anode Stud) w/Pigtail Stud Mount Diode, 150A, 3/8" Stud, 600 PRV Negative (Anode Stud...

12V DC Edgewise Volt Meter, Push-Clamp Mount for Battery Chargers & Voltage Monitoring. 10-15V DC range. Mounts in panel (.030-.150" thickness)...

0-50 Volt DC clamp-mount Heavy-Duty volt meter for battery chargers & voltage monitoring. Mounts in a 2" circular mounting hole. Direct replace...

Original Replacement for Century/Solar Meter 247-138-000 and Various Chargers w/Boost. Snap-in mount to charger panel. Features • Left Movement - ...

60 Minute Mechanical Timer & Hardware Kit This timer can be used to replace older 60 minute electrical and mechanical timers found in many mode...

Heavy-Duty Insulated Red Booster Cable & Battery Charger Clamp, with 500A Isolated Copper Jaw - Excellent for Booster Cables and High-Output Ba...

7" Black Plastic Wheel w/ Diamond Rubber Tread - 3/8" axle bore. 1.5" wide Diamond Rubber Tread. Designed to fit 3/8" axle shaft. For battery charg...

Phase Control SCR/Thyristor for Automatic Chargers (Voltage Regulated)Rated at 50 Amp, 400 Peak Reverse VoltageUsed in Positive Output Chargers (Ca...

0-150 Amp Clamp-Mount External-Shunt DC Amp Meter for High-Output Charging & Current-Monitoring Systems. Current flows through a heavy-duty ext...

0-10 Amp Clamp-Mount Heavy-Duty DC Amp Meter for Battery Chargers. Original Replacement for Various 6-8 Amp Chargers. Also an easy retro-fit in any...

12 Volt Snap-In DC voltmeter. 10-16 Volt scale indicates voltage, and backplate has holes to mount "Charging/Charged" LEDs. Snaps into 1.30"H x 2.2...

610263 - Associated Eqpt Rocker Switch, Load 1.00" x .75" 6029 YA201 (All Hand-Held Load Testers)

Phase Control SCR/Thyristor for Automatic Chargers (Voltage Regulated)Rated at 80 Amp, 400 Peak Reverse VoltageUsed in Positive Output Chargers (Ca...

Stud Mount Diode, 150A, M12 (1/2") Stud, 600 PRV Negative Base w/Pigtail (Anode Stud)Heavy-Duty Standard Recovery Diode, for use in battery charger...

Sheet Metal Screw for Associated Equipment Chargers. This is the black oxide, 5/16" hex head screw used for most Associated Equipment battery charg...

Save $$$ by Rebuilding your Burned-Out Rectifier!   Power Forged 100 Amp Rectifier Rebuild Kit for 696611 & 696613 (Rectifiers with Square Shou...

Volt Meter 6V &12V Inverted Snap-In for Schumacher Chargers - Replaces Schumacher meter 5399200018   The PR18V-6V12DV Voltmeter/Testmeter is an...

PR18V-30DV Voltmeter is easy snap-in installation, no tools required. Bottom movement - needle swings from bottom of scale. Displays battery voltag...

Heavy-Duty Insulated Black Booster Cable & Battery Charger Clamp, with 500A Isolated Copper Jaw - Excellent for Booster Cables and High-Output ...

610242 - Associated Eqpt Thermal Fuse - 6009, 6009A, 6010A, YA167B 6009 6009A 6010A YA167B AC Thermal Fuse 100C. Includes two crimp connectors for ...